How To Repair a Hole in Carpet and Fix Other Common Problems

How to Fix Burned Carpet

You can patch a small hole, tear or burn using techniques that will make the repair virtually invisible. You’ll need a small “plug” of carpet that matches the damaged piece. If you don’t have a remnant, you can steal a piece from inside a closet or underneath a piece of furniture you never intend to move. (This may sound extreme, but it’s a lot cheaper than replacing the entire carpet.)

If you have a “plush”-type carpet with a flat surface and no pattern, you can make an absolutely invisible repair. If your carpet has a color pattern, a textured surface design or looped yarn, you’ll have to be fussier when you cut the plug, and the repair may be visible (but you’re probably the only one who will notice it).

Mark the cut

Be sure the area you’re working in is well-lit. To mark the area you’ll cut out, part the carpet fibers around the damage as if you were parting your hair. Keep the part lines at least 1/2 in. from the damaged spot.

TMB StudioTMB Studio

Cut the damaged carpet and a replacement plug

Cut through the carpet backing along the parts using a sharp, new blade in your carpet knife. Make the cuts as straight as possible, avoiding cutting completely through the carpet pad.

Next, cut a replacement plug using the cutout as a template. To start, make a first cut in the replacement material, using a straightedge to guide your carpet knife. Then, set the cutout on the replacement material with one edge aligned with that first cut. When you lay the cutout on top of the replacement material, ensure their naps are running in the same direction. You can tell which direction the nap is running by rubbing your hand over the carpeting and watching which way the fibers fall or stand up. Once the cutout is lined up correctly, part the fibers around the three uncut sides just as you did before.

Cut along the parts and test-fit the plug in the cutout hole, making sure the nap of the plug matches the nap of the surrounding carpet. If the plug is a little too big, trim off a single row of fibers with sharp scissors (old, dull scissors will tear the fibers).

TMB StudioTMB Studio

Test-fit the replacement piece

Cut pieces of carpet tape and position them in the hole without removing the backing. Cut the ends of the tape diagonally so the pieces will frame the hole without overlapping. The tricky part is getting the tape positioned so it’s halfway under the plug and halfway under the surrounding carpet. A helper makes this easier. Mark a square on the carpet pad to help align each piece later.

TMB StudioTMB Studio

Peel the tape backing

After marking their positions in the hole, remove the pieces from the hole and carefully (this is sticky stuff!) remove the protective backing from the tape. While pulling the carpeting up with one hand, slip the tape pieces back into the prepared hole one piece at a time. Be sure the edges of the tape line up with your markings.

TMB StudioTMB Studio

Place the plug

Now, you’re ready to fit the new plug into the hole. Pull the fibers of the surrounding carpet back from the edges. Push one side of the plug lightly onto the tape to ensure it’s set exactly right—you only have one shot at this. After you’re sure the plug is placed correctly, use your fingers to work in the direction of the nap all the way around the hole as you press the plug down firmly onto each side of the tape.

A carpet tractor will do the best job of meshing the fibers, but a seam roller or even a rolling pin would work, too. Place a telephone book on top of the plug overnight. Trim any fibers sticking up with sharp scissors. Once you’re finished, you’ll be surprised how “invisible” this repair is. You can vacuum and clean your carpeting as you normally would, and this repair should last as long as your carpet does.

TMB StudioTMB Studio

Rescue wet carpet

When carpet gets soaked, you have to act fast. The longer it stays soggy, the more likely it is to stretch out, discolor or get moldy. If a large area is waterlogged, complete replacement may be the best option. But if only a corner or a small room is soaked, you can save the carpet with just a couple of hours of work.

Tear out the soggy pad and dry the carpet

First, go to the corner nearest the wet area, grab the carpet with pliers and pull the carpet off the tack strip. Continue pulling the carpet off the tack strip by hand until you can fold back the entire wet section. Run a fan or two to dry the carpet.

Wet carpet pad is like a big sponge. You have to get rid of it ASAP. Cut around the wet area with a utility knife. Make straight cuts so you have straight seams when you patch in the new pad. If the pad is glued to a concrete floor, scrape it up with a floor scraper. If the pad is stapled to a wood subfloor, just pull up chunks of pad and pry or pull out the staples if you have just a few. For faster removal on a larger area, use a floor scraper. Have garbage bags handy to prevent drips on the carpeting. The wet pad will be heavy. Don’t fill the bags so full that you can’t haul them out without wrecking your back!

Wipe up any water on the floor, then flop the wet carpet back into place. Drying it flat and in place helps the carpet retain its shape. Run fans until the floor and carpet are completely dry. This can take a couple of days.

TMB StudioTMB Studio

Patch in the new pad

Measure the area of pad you need to replace and take a piece of the old pad to a flooring store or home center to find similar replacement pad. The color doesn’t matter, but the new pad must be the same thickness and density as the old pad. Some stores will cut the pad to the size you need.

Fasten the pad to a concrete floor with carpet pad adhesive and duct tape the seams together. On a wood subfloor, all you need is a staple gun and 5/16-in. staples. Use a utility knife to trim off any pad covering the tack strip.

TMB StudioTMB Studio

Reattach the carpet

You need to stretch the carpet toward the tack strip as you refasten it to the wall. If you’re dealing with a corner or a small area, you can use a knee kicker alone (see Photo 3). Starting at one end of the loose carpet, set the head of the kicker about 2 in. from the tack strip and nudge the carpet tight against the wall. Force the carpet into the tack strip with a stiff putty knife. Also tuck the edge of the carpet into the space between the wall and the tack strip with a putty knife. Continue along the wall, moving the kicker over about a few inches each time.

If you’re dealing with a larger area of carpet or if the carpet has stretched out of shape, bubbled or wrinkled after getting wet, you’ll need to rent a power stretcher to restretch the carpet.

Reattach Pulled-Out Carpet

If you have carpet that has pulled loose from a metal threshold, fix it now, before the exposed edge of the carpet begins to fray. If the damage extends more than an inch or so away from the threshold, you won’t be able to make a good-looking repair. Aside from standard hand tools, you’ll need a carpet knife and a knee kicker, which you can get at any rental center. You’ll also need a new metal threshold and 1-1/2-in. ring-shank drywall nails.

Remove the old threshold

This repair is much easier if you first remove the door. You can do it with the door in place, but it’ll take a little longer and you risk scratching the door. Carefully pry up the lip of the existing metal threshold along its entire length using a screwdriver or flat pry bar (Photo 1). Since you’ll be replacing the threshold, you don’t have to worry about wrecking it, but you want to work carefully so you don’t damage the carpet edge even more.

Release the carpet

Once the threshold lip is bent up, use pliers to gently pull the carpeting up from the teeth inside the threshold. Roll the carpet back slightly to get it out of the way (you can leave the carpet pad in place).

TMB StudioTMB Studio

Pull the nails

Pry up the threshold slightly and pull the nails (work from the carpeted side to avoid scratching the hard flooring).

To get an exact measurement for cutting the new threshold, don’t measure the old threshold because it may be kinked. Instead, measure the opening and then cut the threshold with metal snips or a hacksaw.

TMB Studio
TMB Studio

Install the new threshold

If the carpet edge is in good shape, you can place the new threshold exactly where the old one was. If the edge is badly frayed, you must trim off the damage using a carpet knife and a straightedge. Then, position the new threshold farther into the carpeted room to compensate for the width you trimmed off. In most cases, you can place the new threshold about 1 in. from the original position, but not more. If you’ve moved the threshold more than an inch, you may also need to trim the carpet pad so it doesn’t cover the threshold pins.

If you’re working on a wood subfloor, nail down the replacement threshold with 1-1/2-in. ring-shank drywall nails. On a concrete floor, use heavy-duty construction adhesive to glue the threshold to the floor, and allow it to dry for a day before proceeding to the next step.

Attach the carpet

Now, you’re ready to attach the carpet to the new threshold. Starting at one end of the threshold, set the head of the knee kicker about 2 in. from the threshold and kick with your knee to stretch the carpet toward the threshold. Kick firmly, but not with all your strength, or you might rip the carpet. Force the carpet into the threshold teeth with a stiff putty knife. Then, move the kicker over a few inches (the width of the kicker’s head) and repeat the process until you reach the other end of the threshold.

TMB StudioTMB Studio

Lock the carpet down

When you’re done, tuck any loose carpet under nearby baseboards with a stiff putty knife. Finally, pound down the threshold lip with a rubber mallet.

TMB StudioTMB Studio